Electric current

From Wikipedia, the free encyclopedia
Jump to: navigation, search

Electric current is a flow of electric charge through a medium.[1] This charge is typically carried by moving electrons in a conductor such as wire. It can also be carried by ions in an electrolyte, or by both ions and electrons in a plasma.[2]

The SI unit for measuring the rate of flow of electric charge is the ampere, which is charge flowing through some surface at the rate of one coulomb per second. Electric current is measured using an ammeter.[1]

Contents

[edit] Symbol

The conventional symbol for current is I, which originates from the French phrase intensité de courant, or in English current intensity.[3][4] This phrase is frequently used when discussing the value of an electric current, especially in older texts; modern practice often shortens this to simply current but current intensity is still used in many recent textbooks. The I symbol was used by André-Marie Ampère, after whom the unit of electric current is named, in formulating the eponymous Ampère's force law which he discovered in 1820.[5] The notation travelled from France to England, where it became standard, although at least one journal did not change from using C to I until 1896.[6]

[edit] Conduction mechanisms in various media

In metallic solids, electric charge flows by means of electrons, from lower to higher electrical potential. In other media, any stream of charged objects (ions, for example) may constitute an electric current. To provide a definition of current that is independent of the type of charge carriers flowing, conventional current is defined to flow in the same direction as positive charges. So in metals where the charge carriers (electrons) are negative, conventional current flows in the opposite direction as the electrons. In conductors where the charge carriers are positive, conventional current flows in the same direction as the charge carriers.

In a vacuum, a beam of ions or electrons may be formed. In other conductive materials, the electric current is due to the flow of both positively and negatively charged particles at the same time. In still others, the current is entirely due to positive charge flow. For example, the electric currents in electrolytes are flows of positively and negatively charged ions. In a common lead-acid electrochemical cell, electric currents are composed of positive hydrogen ions (protons) flowing in one direction, and negative sulfate ions flowing in the other. Electric currents in sparks or plasma are flows of electrons as well as positive and negative ions. In ice and in certain solid electrolytes, the electric current is entirely composed of flowing ions. In a semiconductor it is sometimes useful to think of the current as due to the flow of positive "holes" (the mobile positive charge carriers that are places where the semiconductor crystal is missing a valence electron). This is the case in a p-type semiconductor.

[edit] Metals

A solid conductive metal contains mobile, or free electrons, originating in the conduction electrons. These electrons are bound to the metal lattice but no longer to an individual atom. Even with no external electric field applied, these electrons move about randomly due to thermal energy but, on average, there is zero net current within the metal. Given a surface through which a metal wire passes, electrons move in both directions across the surface at an equal rate. As George Gamow put in his science-popularizing book, One, Two, Three...Infinity (1947), "The metallic substances differ from all other materials by the fact that the outer shells of their atoms are bound rather loosely, and often let one of their electrons go free. Thus the interior of a metal is filled up with a large number of unattached electrons that travel aimlessly around like a crowd of displaced persons. When a metal wire is subjected to electric force applied on its opposite ends, these free electrons rush in the direction of the force, thus forming what we call an electric current."

When a metal wire is connected across the two terminals of a DC voltage source such as a battery, the source places an electric field across the conductor. The moment contact is made, the free electrons of the conductor are forced to drift toward the positive terminal under the influence of this field. The free electrons are therefore the charge carrier in a typical solid conductor.

For a steady flow of charge through a surface, the current I (in amperes) can be calculated with the following equation:

I = {Q \over t} \, ,

where Q is the electric charge transferred through the surface over a time t. If Q and t are measured in coulombs and seconds respectively, I is in amperes.

More generally, electric current can be represented as the rate at which charge flows through a given surface as:

I = \frac{\mathrm{d}Q}{\mathrm{d}t} \, .

[edit] Electrolytes

Electric currents in electrolytes are flows of electrically charged particles (ions). For example, if an electric field is placed across a solution of Na+ and Cl (and conditions are right) the sodium ions move towards the negative electrode (cathode), while the chloride ions move towards the positive electrode (anode). Reactions take place at both electrode surfaces, absorbing each ion.

Water-ice and certain solid electrolytes called proton conductors contain positive hydrogen ions or "protons" which are mobile. In these materials, electric currents are composed of moving protons, as opposed to the moving electrons found in metals.

In certain electrolyte mixtures, brightly-coloured ions form the moving electric charges. The slow migration of these ions means that the current is visible.

[edit] Gases and plasmas

In air and other ordinary gases below the breakdown field, the dominant source of electrical conduction is via relatively few mobile ions produced by radioactive gases, ultraviolet light, or cosmic rays. Since the electrical conductivity is low, gases are dielectrics or insulators. However, once the applied electric field approaches the breakdown value, free electrons become sufficiently accelerated by the electric field to create additional free electrons by colliding, and ionizing, neutral gas atoms or molecules in a process called avalanche breakdown. The breakdown process forms a plasma that contains enough mobile electrons and positive ions to make it an electrical conductor. In the process, it forms a light emitting conductive path, such as a spark, arc or lightning.

Plasma is the state of matter where some of the electrons in a gas are stripped or "ionized" from their molecules or atoms. A plasma can be formed by high temperature, or by application of a high electric or alternating magnetic field as noted above. Due to their lower mass, the electrons in a plasma accelerate more quickly in response to an electric field than the heavier positive ions, and hence carry the bulk of the current. The free ions recombine to create new chemical compounds (for example, breaking atmospheric oxygen into single oxygen [O2 → 2O], which then recombine creating ozone [O3]).[7]

[edit] Vacuum

Since a "perfect vacuum" contains no charged particles, it normally behaves as a perfect insulator. However, metal electrode surfaces can cause a region of the vacuum to become conductive by injecting free electrons or ions through either field electron emission or thermionic emission. Thermionic emission occurs when the thermal energy exceeds the metal's work function, while field electron emission occurs when the electric field at the surface of the metal is high enough to cause tunneling, which results in the ejection of free electrons from the metal into the vacuum. Externally heated electrodes are often used to generate an electron cloud as in the filament or indirectly heated cathode of vacuum tubes. Cold electrodes can also spontaneously produce electron clouds via thermionic emission when small incandescent regions (called cathode spots or anode spots) are formed. These are incandescent regions of the electrode surface that are created by a localized high current flow. These regions may be initiated by field electron emission, but are then sustained by localized thermionic emission once a vacuum arc forms. These small electron-emitting regions can form quite rapidly, even explosively, on a metal surface subjected to a high electrical field. Vacuum tubes and sprytrons are some of the electronic switching and amplifying devices based on vacuum conductivity.

[edit] Superconductivity

Superconductivity is a phenomenon of exactly zero electrical resistance and expulsion of magnetic fields occurring in certain materials when cooled below a characteristic critical temperature. It was discovered by Heike Kamerlingh Onnes on April 8, 1911 in Leiden. Like ferromagnetism and atomic spectral lines, superconductivity is a quantum mechanical phenomenon. It is characterized by the Meissner effect, the complete ejection of magnetic field lines from the interior of the superconductor as it transitions into the superconducting state. The occurrence of the Meissner effect indicates that superconductivity cannot be understood simply as the idealization of perfect conductivity in classical physics.

[edit] Current density and Ohm's law

Current density is a measure of the density of an electric current. It is defined as a vector whose magnitude is the electric current per cross-sectional area. In SI units, the current density is measured in amperes per square metre.

I = \vec{J} \cdot \vec{A}

where I is current in the conductor, J is the current density, and A is the cross-sectional area. The dot product of the two vector quantities (A and J) is a scalar that represents the electric current.

Current density (current per unit area) J in a material is proportional to the conductivity σ and electric field E in the medium:

J =\sigma E \,

Instead of conductivity, a reciprocal quantity called resistivity ρ, can be used:

J = {E \over \rho}

Conduction in semiconductor devices may occur by a combination of drift and diffusion, which is proportional to diffusion constant D and charge density \alpha_q. The current density is then:

J =\sigma E + D q \nabla n ,

with q being the elementary charge and n the electron density. The carriers move in the direction of decreasing concentration, so for electrons a positive current results for a positive density gradient. If the carriers are holes, replace electron density n by the negative of the hole density p.

In linear anisotropic materials, σ, ρ and D are tensors.

In linear materials such as metals, and under low frequencies, the current density across the conductor surface is uniform. In such conditions, Ohm's law states that the current is directly proportional to the potential difference between two ends (across) of that metal (ideal) resistor (or other ohmic device):

I = {V \over R} \, ,

where I is the current, measured in amperes; V is the potential difference, measured in volts; and R is the resistance, measured in ohms. For alternating currents, especially at higher frequencies, skin effect causes the current to spread unevenly across the conductor cross-section, with higher density near the surface, thus increasing the apparent resistance.

[edit] Drift speed

The mobile charged particles within a conductor move constantly in random directions, like the particles of a gas. In order for there to be a net flow of charge, the particles must also move together with an average drift rate. Electrons are the charge carriers in metals and they follow an erratic path, bouncing from atom to atom, but generally drifting in the opposite direction of the electric field. The speed at which they drift can be calculated from the equation:

I=nAvQ \, ,

where

I is the electric current
n is number of charged particles per unit volume (or charge carrier density)
A is the cross-sectional area of the conductor
v is the drift velocity, and
Q is the charge on each particle.

Typically, electric charges in solids flow slowly. For example, in a copper wire of cross-section 0.5 mm2, carrying a current of 5 A, the drift velocity of the electrons is on the order of a millimetre per second. To take a different example, in the near-vacuum inside a cathode ray tube, the electrons travel in near-straight lines at about a tenth of the speed of light.

Any accelerating electric charge, and therefore any changing electric current, gives rise to an electromagnetic wave that propagates at very high speed outside the surface of the conductor. This speed is usually a significant fraction of the speed of light, as can be deduced from Maxwell's Equations, and is therefore many times faster than the drift velocity of the electrons. For example, in AC power lines, the waves of electromagnetic energy propagate through the space between the wires, moving from a source to a distant load, even though the electrons in the wires only move back and forth over a tiny distance.

The ratio of the speed of the electromagnetic wave to the speed of light in free space is called the velocity factor, and depends on the electromagnetic properties of the conductor and the insulating materials surrounding it, and on their shape and size.

The magnitudes (but, not the natures) of these three velocities can be illustrated by an analogy with the three similar velocities associated with gases.

  • The low drift velocity of charge carriers is analogous to air motion; in other words, winds.
  • The high speed of electromagnetic waves is roughly analogous to the speed of sound in a gas (these waves move through the medium much faster than any individual particles do)
  • The random motion of charges is analogous to heat – the thermal velocity of randomly vibrating gas particles.

This analogy is extremely simplistic and incomplete: The rapid propagation of a sound wave does not impart any change in the air molecules' drift velocity, whereas EM waves do carry the energy to propagate the actual current at a rate which is much, much higher than the electrons' drift velocity. To illustrate the difference: The sound and the change in the air's drift velocity (the force of the wind gust) cross distance at rates equaling the speeds of sound and of mechanical transmission of force (not higher than rate of drift velocity); while a change in an EM field and the change in current (electrons' drift velocity) both propagate across distance at rates much higher than the actual drift velocity. You can hear wind much earlier than the force of the gust reaches you, but you do not observe a change in an EM field earlier than you can observe the change of current.

[edit] Electromagnetism

According to Ampère's law, an electric current produces a magnetic field.

Electric current produces a magnetic field. The magnetic field can be visualized as a pattern of circular field lines surrounding the wire.

Electric current can be directly measured with a galvanometer, but this method involves breaking the electrical circuit, which is sometimes inconvenient. Current can also be measured without breaking the circuit by detecting the magnetic field associated with the current. Devices used for this include Hall effect sensors, current clamps, current transformers, and Rogowski coils.

The theory of Special Relativity allows one to transform the magnetic field into a static electric field for an observer moving at the same speed as the charge in the diagram. The amount of current is particular to a reference frame.

[edit] Conventions

The electrons, the charge carriers in an electrical circuit, flow in the opposite direction of the conventional electric current.
The symbol for a battery in a circuit diagram.

A flow of positive charges gives the same electric current, and has the same effect in a circuit, as an equal flow of negative charges in the opposite direction. Since current can be the flow of either positive or negative charges, or both, a convention for the direction of current which is independent of the type of charge carriers is needed. The direction of conventional current is defined arbitrarily to be the direction of the flow of positive charges.

In metals, which make up the wires and other conductors in most electrical circuits, the positive charges are immobile, and the charge carriers are electrons. Because the electron carries negative charge, the electron motion in a metal conductor is in the direction opposite to that of conventional (or electric) current.

[edit] Reference direction

When analyzing electrical circuits, the actual direction of current through a specific circuit element is usually unknown. Consequently, each circuit element is assigned a current variable with an arbitrarily chosen reference direction. When the circuit is solved, the circuit element currents may have positive or negative values. A negative value means that the actual direction of current through that circuit element is opposite that of the chosen reference direction. In electronic circuits the reference current directions are usually chosen so that all currents flow toward ground. This often matches conventional current direction, because in many circuits the power supply voltage is positive with respect to ground.

[edit] Occurrences

Natural examples include lightning and the solar wind, the source of the polar auroras (the aurora borealis and aurora australis). The artificial form of electric current is the flow of conduction electrons in metal wires, such as the overhead power lines that deliver electrical energy across long distances and the smaller wires within electrical and electronic equipment. In electronics, other forms of electric current include the flow of electrons through resistors or through the vacuum in a vacuum tube, the flow of ions inside a battery or a neuron, and the flow of holes within a semiconductor.

[edit] Current measurement

Current can be measured using an ammeter.

At the circuit level, there are various techniques that can be used to measure current:

  • Shunt resistors[8]
  • Hall effect current sensor transducers
  • Transformers (however DC cannot be measured)
  • Magnetoresistive field sensors[9]

[edit] See also

[edit] References

  1. ^ a b Lakatos, John; Oenoki, Keiji; Judez, Hector; Oenoki, Kazushi; Hyun Kyu Cho (March 1998). "Learn Physics Today!". Lima, Peru: Colegio Dr. Franklin D. Roosevelt. http://library.thinkquest.org/10796/ch13/ch13.htm. Retrieved 2009-03-10. 
  2. ^ Anthony C. Fischer-Cripps (2004). The electronics companion. CRC Press. p. 13. ISBN 9780750310123. http://books.google.com/?id=3SsYctmvZkoC&pg=PA13. 
  3. ^ T. L. Lowe, John Rounce, Calculations for A-level Physics, p. 2, Nelson Thornes, 2002 ISBN 0748767487.
  4. ^ Howard M. Berlin, Frank C. Getz, Principles of Electronic Instrumentation and Measurement, p. 37, Merrill Pub. Co., 1988 ISBN 0675204496.
  5. ^ A-M Ampère, Recuil d'Observations Électro-dynamiques, p. 56, Paris: Chez Crochard Libraire 1822 (in French).
  6. ^ Electric Power, vol. 6, p. 411, 1894.
  7. ^ "Lab Note #106 Environmental Impact of Arc Suppression". Arc Suppression Technologies. April 2011. http://arcsuppressiontechnologies.com/Documents/Lab%20Note%20106%20-%20APR2011%20-%20Environmental%20Impact.pdf. Retrieved March 15, 2012. 
  8. ^ What is a Current Sensor and How is it Used?. Focus.ti.com. Retrieved on 2011-12-22.
  9. ^ Andreas P. Friedrich, Helmuth Lemme The Universal Current Sensor. Sensorsmag.com (2000-05-01). Retrieved on 2011-12-22.

[edit] External links

Personal tools
Namespaces

Variants
Actions
Navigation
Interaction
Toolbox
Print/export
Languages